High-concerned chemical : none
is_d : Yes
Dissipation Power : 1A
Supply Voltage : 5V
Application : MOBILE PHONE
Type : Voltage Regulator
Origin : Mainland China
Condition : New
Operating Temperature : -40-+85
Electronic products : For Arduino STM
5Pcs TP4056 Lithium Battery Charger Module 5V 1A Protection Dual Functions 18650 Li-ion Micro USB Type-C Mini Charging Board DIY.
Key Features & Benefits
Three Interface Versions: Micro USB, Type-C, or Mini USB—choose the one that fits your cables. Charge 18650 cells with any standard 5V phone charger.
️ Charge + Protection Dual Functions: Integrated TP4056 charge IC and DW01 protection circuit. Overcharge (4.2V±1%), over-discharge (2.5V cutoff), and short circuit protection keep your batteries safe.
5V 1A Standard Charging: Max 1A constant current charging with auto-stop when full. Red/Blue LED indicator: Red = Charging, Blue = Full. Status at a glance.
Ultra-Compact, Embed Anywhere: Mini PCB easily solders into projects or battery holders. The essential building block for DIY power banks, solar storage, and toy mods.
Plug & Charge, Zero Learning Curve: B+ to battery positive, B- to battery negative, plug USB power—done. Simple enough for complete beginners.
Product Description
One module is all you need to charge 18650 Li-ion cells. The TP4056 is the most trusted Li-ion charging solution in the DIY electronics community, combining charge management and battery protection on one tiny board. Just a 5V phone charger and USB cable deliver a safe 1A charge. Onboard red/blue LEDs show charge status clearly. Built-in triple protection prevents overcharging, over-discharging, and short circuits. Three interface versions available—Micro USB, Type-C, Mini USB—to match your cable preference.
Quick Start Guide & Important Tips
What It Does & What You Need
This module does: Charge 3.7V/3.6V Li-ion cells (18650 etc.) from a 5V USB source at up to 1A. Integrated overcharge, over-discharge, and short circuit protection.
This module is NOT: A LiFePO4 charger. It does NOT boost battery voltage to 5V. It is NOT a power bank mainboard.
You will need: A 5V USB charger (1A+ output), a USB cable matching the version, a 18650 Li-ion cell.
Wiring & Usage
1.Connect Battery: B+ to battery positive (red), B- to battery negative (black). ️ Reverse polarity will instantly destroy the module!
2.Power Up: Plug the USB cable into the module and 5V charger. Red LED = Charging.
3.Wait for Full: Blue LED = Fully charged (~4.2V). Module stops automatically.
️ First Activation: After connecting the battery, the output terminals (OUT+/OUT-) may show no voltage. Apply 5V charge power for a few seconds to activate the protection circuit, then output will work normally.
Important Notes & Common Questions
Charger Requirement: Use a 5V USB charger rated 1A or higher. Old PC USB ports (0.5A) may charge extremely slowly or not at all.
Type-C Note: The Type-C version only supports USB-A to Type-C cables. It does NOT support Type-C to Type-C (C-to-C) charging.
Disconnect Load During Charge: Disconnect any load from OUT+/OUT- while charging, or charging may be affected.
No output voltage after connecting battery?
The protection circuit needs activation. Apply 5V charge power briefly and output will resume.
Red LED keeps blinking?
The battery may be deeply discharged (<2.5V). The module is in trickle charge mode. It will switch to constant current once voltage rises. Or the battery may be damaged.
Can I charge multiple 18650s in parallel?
This is a single-cell charger. Parallel charging is theoretically possible but slower, and cells must have closely matched voltages.
Specifications
Note: All dimensions measured manually, allow 1-3mm tolerance. Actual color may vary slightly from pictures due to lighting. Please refer to the physical item.
Package Includes
As selected interface version and quantity (TP4056 Charging Protection Module × Selected Quantity)
label:yes
GaN support: no
Plug type: European socket
No-delivery refund
